THE DYNAMIC BUCKLING OF AN ORTHOTROPIC CYLINDRICAL THIN SHELL UNDER TORSION VARYING AS A POWER FUNCTION OF TIME

The subject of this investigation is to study the buckling of orthotropic cylindricalthin shells under torsion,which is a power function of time.The dynamic stability and compati-bility equations are obtained first.These equations are subsequently reduced to a time dependentdifferential equation with variable coefficient by using Galerkin's method.Finally,the critical dy-namic and static loading,the corresponding wave numbers,the dynamic factors,critical time andcritical impulse are found analytically by applying the Ritz type variational method.Using thoseresults,the effects of the variations of the power of time in the torsion load expression,of theloading parameter,the ratio of the Young's moduli and the ratio of the radius to thickness onthe critical parameters are studied numerically.It is observed that these factors have appreciableeffects on the critical parameters of the problem in the heading.     

煤层底板原位综合测试及突水危险性评估

在实施井下钻孔水压致裂地应力测量的同时,评价岩层阻水性能,确定导升带高度,做到一孔多用。测试区实际观测表明,泥岩、粉砂岩、中砂岩、灰岩阻水性能由大到小,导升高度则由小变大,平均导升高度约32m; 地应力测量表明,该测试区原始地应力状态为SH＞Sv＞Sh,最大水平主应力方向NE至NEE。突水临界指数评价表明,-550m水平采煤工作面掘进时突水的可能性较大,应当采取防范措施。     

Three-dimensional stability of a rectangular plate under uniaxial tension

The paper studies the three-dimensional stability of an isotropic, linear elastic, rectangular plate under a uniform tensile load applied to its sides. The concept of free strains is used to reduce the three-dimensional problem to a two-dimensional one. It is solved using the three-dimensional linearized theory of stability. An approximate solution of the buckling problem is obtained by the finite-difference method. Numerical results are presented __________ Translated from Prikladnaya Mekhanika, Vol. 42, No. 7, pp. 116–123, July 2006.     

Generalized sensitivity and probabilistic analysis of buckling loads of structures

The imperfection sensitivity law by Koiter played a pivotal role in the early stage of research on initial post-buckling behaviors of structures, but seems somewhat overshadowed by numerical approaches in the computer age. In this paper, to make this law consistent with practical application, the law is extended to implement the influence of a number of imperfections, and the second-order (minor) imperfections are considered, in addition to the first-order (major) imperfections considered in the Koiter law. Explicit formulas are presented to be readily applicable to the numerical evaluation of imperfection sensitivity. A procedure to describe the probabilistic variation of critical loads is presented for the case where initial imperfections of structures are subject to a multivariate normal distribution; the formula for the probability density function of critical loads is derived by considering up to the second-order imperfections. The validity and usefulness of the present procedure are demonstrated through the application to truss structures.     

一种考虑拉伸保持效应的多轴疲劳寿命模型

通过定义考虑拉伸保载效应的CFI因子(creep-fatigue interaction factor)，将拉伸蠕变损伤和疲劳损伤进行非线性耦合. 根据断裂实验的观察，针对拉伸主 导的裂纹萌生、扩展及破坏的多轴疲劳问题，给出了一个基于临界面方法的能量型高温多轴 疲劳寿命预测模型. 所给出的模型可对不同温度、不同载荷特点、不同保载时间的多轴疲劳 寿命进行预测，模型的材料参数不依赖于温度和载荷. 并且此方法可以很方便地推广到其它 因素主导破坏的高温多轴疲劳寿命预测. 通过拟合高温合金Udimet720Li单轴带保持时间的 低循环疲劳(low cycle fatigue, LCF)寿命试验数据，得到了材料常数. 结合黏 塑性有限元分析方法，对高温双轴带保载循环载荷下Cruciform试件的寿命进行了 预测，预测结果基本落在2倍分散带内，达到工程的要求，证明了该模型的有效性.     

软铁磁薄板磁弹性屈曲的理论模型

铁磁弹性薄板的磁弹性屈曲问题一直作为电磁——弹性力学相互作用的一个基本模型进行研究，而作用在其磁介质上的磁力计算则是定量理论预测准确与否的关键．到目前为止，文献上已有的理论模型对悬臂铁磁梁式悬臂板在横向磁场中磁弹性屈曲的理论预测值始终高于实验值，有的甚至相差１００％左右．本文基于电磁力计算的微观安培电流模型，严格给出了软铁磁薄板等效横向磁力的宏观计算表达式．在此基础上，建立了电磁——力学相互耦合作用的非线性理论模型．该模型能描述铁磁薄板结构在非均匀横向磁场环境中的磁弹性失稳（或屈曲）．其定量分析采用了有限元法和有限差分法相结合．数值结果显示：本模型给出的磁弹性屈曲的临界磁场值与实验值符合良好．与此同时，文中还对文献中认为较成功的Ｍｏｏｎ－Ｐａｏ模型的基本假设进行了分析．定量结果发现：Ｍｏｏｎ－Ｐａｏ理论模型的基本假设仅在梁式板的长厚比Ｌ／ｈ比较大时（约在２００左右），是可以接受的，而当Ｌ／ｈ较小时，该假设将导致理论值与实验值的较大误差．Ｌ／ｈ比值越小，理论值与实验值的误差越大     

Internal waves around a disturbance in a fluid with arbitrary stratification and background shear flow

A three-dimensional ray theory is presented for calculating the phase configuration of internal waves around a moving disturbance in a flow with arbitrary stratification and background shear. The theory is applied to two-dimensional stratified shear flows which have been produced in the laboratory and good agreement is shown between the theoretical and experimental phase configurations. Good agreement is also shown when caustics and critical levels are present. This paper includes the wave systems arising from a combined translation and oscillatory motion of a source and it shows how distinct systems of waves arise from each, type of motion under different background conditions. This paper shows that for two-dimensional steady wave systems the critical level is at a well defined height which is independent of wavenumber but in three dimensions the critical height can in general vary with wavenumber.     

Stability of longitudinally corrugated cylindrical shells under uniform surface pressure

The buckling problem for longitudinally corrugated cylindrical shells under external pressure is solved. The solution makes practically exact allowance for the geometry and buckling modes of the shell. The inaccuracy of the results is due to the assumption that the subcritical state is momentless. Shells consisting of cylindrical panels of smaller radius and noncircular shells with sinusoidal corrugations are analyzed for stability. The practical applicability of such shells is demonstrated __________ Translated from Prikladnaya Mekhanika, Vol. 43, No. 11, pp. 66–79, October 2007.     

An experimental investigation on pool boiling heat transfer enhancement using Cu-Al2O3 nano-composite coating

Pool boiling heat transfer performances of Cu-Al₂O₃-coated copper surfaces have been studied experimentally for its potential use in heat transfer applications. In the present study, a two-step electrochemical deposition method is examined. This method provides an easy control on surface properties such as porosity and coating thickness. The deposition method is studied carefully and responsible surface morphology parameters are reported. After performing the pool boiling experiments on coated surfaces with DI water, the maximum critical heat flux of 1800 kW/m² and heat transfer coefficient of 193 kW/m² K, which are 68% and 260% higher than that of bare surface, respectively.